Quick comparison between:

Whites TreasureMaster
Teknetics EuroTek Pro

Use search box below to compare Whites TreasureMaster with something else

Whites TreasureMaster
Teknetics EuroTek Pro
Feature comparison between Whites TreasureMaster and Teknetics EuroTek Pro
Options Whites TreasureMaster Teknetics EuroTek Pro
Detector Type Coin and Relic Detector Coin and Relic Detector
Price $299 $300
Manufactured in 2015 2013
Battery Type 2 AA 9V
Weight (Lbs.) 2.8 2.5
Operating frequency 7.812kHz. 7.81 kHz.
Display Yes Yes
Backlight No No
Target ID 8-Segment 99 Segment+Audio
Tone ID 4 Tones 3 Tones
Search Modes
  • Coin & Jewelry.
  • Beach.
  • Relics.
  • All Metal.
  • Pinpoint.
  • Dicriminate
Ability to change coils Yes Yes
Ground balance Auto Auto
Waterproof Coil only Coil only
Warranty 3 Years 5 Years
Number of Reviews graph 3
graph 1
graph 13
graph 1
graph 1
graph 1
Avg. User Rating 4.00 4.50
Avg. Durability Rating 4.25 4.25
Avg. Ease of Use Rating 4.75 4.69
Avg. Depth Rating
Depth value
Depth value

Most helpful review for Whites TreasureMaster

Pro features, amateur price.
It's been a very long time since we've seen anything TRULY new from the big "W". The MX5 was the last 'new' machine but was based on MXT technology. While it did pretty well, it never really seemed to find it's market. It's priced up there with the AT Pros but never garnered the respect the AT Pro gets.

Enter the Treasuremaster. I've been detecting 30 years, and I've used 'em all. This little machine has more 'pro' features than any other machine out there in it's price range. It's sensitive, deep, easy to use, lightweight and should give that little banana colored beeper some serious competition as the Treasuremaster isn't even in the same class as the Garrett Ace, but it's priced where the Ace is.

Real automatic ground balance, VCO pinpointing, adjustable target volume, 4 tone ID, 8 segment disc, threshold hunt (a sensitivity feature that no other detector has under $300), runs on 2 AA batteries for 20 hours and it's weatherproof. (Let's call it rainproof). It's weighs in at about 3 lbs. A little extra 'beef' than the featherlight detectors like the Tek Delta 4000 but the extra heft makes it feel like a better built detector.

I've had it out about 5 times now and have re-hunted some sites that I've been over. Finding a lot of clad. I'm not finding much in the way of serious keepers, but that's the fault of my location and not the detector. The detector hits coins very solidly and will lock on a target. Target ID is pretty much the same as other White's machines. 70's-80's are dimes/pennies/quarters, nickels ring up at a consistent 20-24, zincs read 59-61. I hunt in Georgia red clay and it seems to handle the hot soil well. You can hear the detector update the ground balance if you lift the coil about waist high and walk with it in the air. You'll hear a deep beep every few seconds.

Using it is as easy as turning it on, use the UP/DOWN arrow by the Options button to set a slight threshold and start swinging. If the detector falses, simply turn the sensitivity down using the +/- buttons. The various settings are selected by pressing the Option button and cycling thru the various tweakable settings.

The display numbers are large and easy to read. Not as big as the Fisher F series, but much easier to read than even my expensive MXT. I found the 4 tone ID a little annoying especially in hotter ground and it can false and cause some random low tones. Setting the tone ID to 2 tones solved that. Overall, the Treasuremaster is MUCH more machine than the Coinmaster/Pro series it replaces and MUCH more machine than it's target competition the Garrett Ace series. I think given some time, the Treasuremaster should become a popular choice in the vast array of detectors out there.
Jay Emm from Georgia

Thumbs up! 48
Read all reviews for Whites TreasureMaster

Most helpful review for Teknetics EuroTek Pro

What I discovered about the eurotek pro
Eurotek Pro Field Test By Mark Gillespie 2013.
With all the metal detecting publicity on both the internet and TV it is nice to see a detector manufacturer release a machine like the Teknetics Eurotek Pro. Originally designed for the extreme hunting conditions of Europe and other areas where iron is common, it will work well as a multipurpose machine.

The machine has an extremely fast re-tune speed which is necessary in the areas where iron is the most common item in the ground, and an expanded iron discrimination feature not found in a machine priced at this level. The Eurotek Pro with the 8” concentric coil sells for only $219 or with the 11” DD coil for only $299. It also has a first ever volume control feature that is not available in any other detector on the market, which I will discuss later.

One of the first tasks I perform after assembly of a new detector is to check how it performs with a set of targets in air test.
Over the years, I have kept a detailed record of air test results for many detectors using the same set of both ferrous and non-ferrous targets. Doing these tests gives a good indication how it might do on targets in the ground and allows me to see where each target registers on the ID number scale.

This machine performed well in comparison to other more expensive machines, but surprised me by the low conductor, coil to target distances. I was expecting a low frequency of 7.8 kHz to be more sensitive to the high conductors but found the opposite to be true. At first, I thought there must be a mistake, but after an evening of testing, I knew the machine functions were deliberate. Low conductors are where gold and many European relics are. Some of the most valuable relics are in the lower conductor category. Actual air test results indicated a 5 1/2 percent increase in sensitivity (a greater coil to target air test distances on each the 8” and 11” coils) for the lower conductors, especially the lower conductors from a US nickel down.

Now personally, I would rather find a gold ring instead of a silver dime or quarter any day. Moreover, with gold hovering around $1500 per ounce a couple of small rings will pay for this machine quickly. Then, it’s all profit.

My next stop is the test garden where I have many coins and relics buried in depths from two to eight inches. Many of these targets are in and around iron nails and some aluminum trash. In addition to this, the test garden has been undisturbed for more than 6 years, which gives a more realistic ground test. I decided to start with the 8” concentric coil and default settings of sensitivity 7, discrimination 0 and volume 7.
At these settings, the majority of targets gave a good audio response.

During the next couple of hours, I adjusted the sensitivity, discrimination and volume to different levels to see how each target responded and found all coins buried up to 4” deep would give a good audio at a sensitivity setting of four. I had two targets that could not be detected even with sensitivity maxed out and they were an 8” quarter and a small copper rivet a little larger than a pencil eraser at 7” deep.
However, switching over to the 11” DD coil, the quarter gave a good audio response at a sensitivity level of eight but the rivet required a setting of 10. Overall, I was pleased with the test garden results.

As a final note, I would like to mention the volume control, which I really like especially in the areas where nails are common. I personally like to hear the iron but not loud so my preference for this setting is 11. At volume 11, the iron gives a very low volume, softer response that I can deal with. The following is a quick rundown of the volume feature.

· Volume settings from 1-9 increase the volume for both ferrous and non-ferrous targets equally.
· Volume setting of 10 and ferrous targets are silent, but non-ferrous targets are at their maximum volume level.
· Volume settings from 11-20 only increase the volume of iron while leaving the non-ferrous targets at maximum volume.

The Eurotek Pro is the first detector that allows independent DIGITAL adjusting of the volume levels for ferrous and non-ferrous targets. In addition, the machine also has an iron icon that will flash to alert the user of iron, regardless of where the discrimination or volume levels are set.
The pinpoint mode can be set to either centimeters or inches. Finally, when the user finds the settings that he or she likes, they can be saved as the default startup settings until the machine is reset.

Over the next several weeks, I took the Eurotek Pro to many different sites and made some very important observations listed below. Please note the two options used: Eurotek with 8” concentric coil:
· Any target that can be detected with a sensitivity setting of 10 can, in most cases, be detected at a setting of 6 if the depth is less than 6”
· Dime size targets at 6” deep would quit giving an audio if the sensitivity level dropped below 6
· The default setting of 7,0,7 was an adequate setting for each location I visited
· When hunting in an area where there are many iron nails a volume setting of 11 will allow a very soft, low volume audio to indicate iron is present
· In clean ground (not much trash or nails) with coins and relics buried up to 4” deep the concentric coil will give an audio if the target is anywhere under the coil
· In clean ground (not much trash or nails) with coins and relics deeper than 5” you should overlap about ½ the diameter of the coil in order to get a consistent audio response
· Most locations the machine would run at sensitivity 10 with no EMI problems
· When EMI was high (overhead power lines and transformers), a sensitivity level of 8 will allow quiet operation, I never had to go below this setting to quiet the machine down
· Small rusted iron items (nails) co-located with non-ferrous targets tend to cause the ID numbers to average up
· Larger rusted items located with non-ferrous targets tend to bring the ID numbers down
· Target ID numbers are very accurate on coin size targets, most cases I could identify coins prior to digging them up.

Eurotek with 11” DD coil:
· Provides better coverage and responses in trashy areas
· Will be a bit more noisy in trashy areas
· A little more susceptible to EMI issues
· Better depth than the 8” concentric coil even with lower sensitivity settings
· Better detection of targets that are very close to each other
· Target ID numbers are very accurate on coin size targets, most cases I could identify coins prior to digging them up

In summary, even though the Eurotek Pro designed specifically for the conditions in Europe, it will function as a multipurpose detector too. Lacking the typical target icons to aid in target identification the machine is equipped with a target ID system that ranges from 1-99 which represents the targets electrical conductivity.

Once learned these numbers can help identify many different type of coins especially the US ones. The ET Pro equipped with the 11” DD coil performs very well as a relic machine, especially old home sites where iron is so common.
Very fast recovery speed combined with an expanded iron discrimination feature is essential in effectively hunting this type of site.

The volume of the iron audio can be adjusted to suit the operator without increasing the discrimination level. Very well balanced, not front heavy like so many other machines in the same price range and can be used for extended hours without unnecessary fatigue. It looks like Teknetics has another winner.
Mark Gillespie from Virginia

Thumbs up! 68
Read all reviews for Teknetics EuroTek Pro